The technology of erecting barriers is the property of developers. No secrets, everything is available and open! installed the frame and mounted the filling of the corrugated board or fence. However, any amateur performance when installing a fence is excluded. Deviations from the step-by-step instructions will not bring any pleasant minutes in the future. How can you not use useful advice!
Content
Euroshield Photo
The appearance on the territory of our habitat euro fence we owe to manufacturers and manufacturers of stainless rolled products with a wide program of brands - the companies of Belgian ArcelorMittal and German ThyssenKrupp. The know-how of manufacturing lamellas made of steel sheet served as an accelerator for the creation of a metal fence.
Euroshield metal is a product of cold-rolled steel, galvanized high quality - corrugated board, industrialized to individual elements (lamellae) with a polymer coating.
Collected from the euro-barrel sectional fences favorably differ from existing structures, combining the strength of the metal, the durability of the construction and the unpretentious maintenance. The metal fence has become popular due to the unhindered movement of air on the sites and the original appearance.
The cost of the fence from the euro trolley is acceptable for the purchase of lightweight lamellas and steel structures galvanized with a polymer coating and increased rigidity. We can not hide the fact that many of the fences are assembled and assembled from the euro-barrel.
Helpful Tips
The profile of the euro-barrel is varied from rectangular to semi-circular. The dimensions of the lamellae are from 80 to 128 mm in width.
If the euro barrel for you is still Terra Incognito, then this video by the way.
Types of euro-barrier
There are euro-barrier single-sided or double-sided fastening. For single-sided fastening, the placement of racks or lamellas of the fence is single-row with clearance, double-sided fastening provides two-sided arrangement of the slats in staggered order. Let's tell, Euroshield (side A) and (side B) are used for traditional sewing with a distance between lamellas up to 40 mm. For two-sided sewing ("Blinds"), sides A and B are used with offset lamella installation.
To install a fence from the euro trolley, it is recommended to prepare the frame and fix the pins with the mounting clip on the poles.
Fence installation technology
Enlarged, the technology of the fence device consists of the stages:
- on the chosen level ground, the future location of the pillars
- under the support pillars, holes are drilled or drilled in the earth to a depth of 800 mm
- produce installation of supporting poles with casting a hole with a concrete mix, for brick poles, organize masonry
- on the supports in the mounting clips fix the transverse lugs, on which the installation of snap
- the installation of the fence and its securing on horizontal lags
- on the profile metal poles a plug is installed.
According to the basic technology, you can install the fence in certain ways.
ways to erect a metal fence
There are principally distinctive ways of arranging fences for a fence:
- barrage with metal posts
- fence with decorative brick pillars
- metal bar on the belt foundation
- fence with brick pillars on a monolithic foundation.
Any method is possible for a manual installation. Let's say that experts consider a budget option a fence on metal poles.
Fence from the euro barrel with your own hands
The installation begins with the installation of supports that can be installed in the following ways: by padding or backfilling into the drilled hole and concreting.
poles for fence from euro barrier
The installation of support pillars is considered a fundamental measure when creating a fence. Possible installation options: * Metal poles for fence or brick.
Metal
For poles, profile pipes with a cross section of 60x60x2, 80x80x3 and 100x100x3 mm, as well as screw piles D76 and D89, are widely used. In practice, preference is given to profile pipes section 80h80h3, capable of withstanding the weight of the picket at maximum load.
For the fastening of the lamellas, cross-section frame legs are used from the profile pipe 40x40x2 or 50x25x2mm. The fastening of poles is done by padding and backfilling. The bottom of the hole under the pillar is strengthened, after installing the pipes are covered with gravel and rammed. Fastening of each lamella of the fence is made by 4 self-tapping screws - 2 per upper and lower lag.
Helpful Tips
The choice of the section of the profile pipe as supporting poles must be confirmed by an approximate calculation, the initial data of which are the parameters of the total length of the fence and the number of poles. The number of necessary lamellas is calculated by dividing the length of the guard by the width of the lamellae, taking into account the width of the gap between the lamellae. For a two-sided installation, the result is doubled.
ways to fasten a metal fence
There are several ways to horizontally and vertically fix the metal fence: using welding and using special fastening systems and holders. Fixing X-brackets allow to fix the log horizontally on vertically mounted support poles.
Step-by-step instruction
Step 1. Installation of bearing support pillars.
Step 2. Installation of transverse logs according to the design height and weight of the fence.
Step 3. Attaching the pins
Step 4. Installation of plugs on profile pipes.
Placement of a metal euro-barrel on metal poles is the most accessible way.
Useful tips for assembling the Euro barrel are shown here.
More difficult and costly is the method of installation on a strip foundation, especially if brick poles are involved.
Brick
For the installation of brick poles for the fence, it is necessary to erect formwork and a foundation for the brickwork, in view of the solid weight of the entire structure. Tape monolithic foundation will allow the construction of fences with a height of up to 5 m, with a well-chosen pattern of the euro fence, the fence has a presentable appearance
Step-by-step instruction
Step 1. Marking the plot for brick poles
Step 2. Excavating a trench with sand and gravel
Step 3. Laying of reinforcement and installation of supporting poles with subsequent pouring of the foundation with concrete
Step 4. Strapping each pillar with brick
Step 5. Installing the elements for fixing the transverse lag
Step 6. Pole stitch fixing.
Fastening of transverse logs for mounting the fence to brick poles and supporting profiles is done on special brackets using dowels and self-tapping screws.
Arrangement of pillars of brick for fencing, shown in the video.
Loading ...