The installation of the door frame does not end on its own even after the last screw or screw is installed. Now it is necessary to think out what material to make the doorways and what kind of platbands to install. We hasten to assure that after installation of the box, all other work on the formation of slopes and the installation of clypeus is so simple!
Door frame installation
If you decide to install the door yourself, first select the right door model http://www.rf-dveri.ru/ and prepare the necessary tools and materials.
Installation of the door frame, slopes and finishing with beautiful platbands is a laborious and laborious process. A simple, at first glance, job requires a clear implementation of the technological operations for installation.
What are the stages of the assembly and subsequent installation of the door frame?
The installation of the door box consists of the following steps:
• door box assembly
• marking and installation of the box in place
• fastening and aligning the edges of the box
• Hanging the door and checking its operability.
The process of assembling the door box begins with the detachment of the warheads, taking into account the recommended technological gap between the door leaf and the floor. The connection of the rounded ends of the edge bars to the ends of the upper part of the box is made.
Angles are joined using self-tapping screws. Next, the layout of the installation site is made, so make grooves where the door frame will be installed, the dimensions of which must be strictly maintained. Now you can install the assembled door frame in the opening, making sure it is properly positioned. It is recommended to use the level to check the vertical and horizontal position of the door frame. The door box should be strictly vertical.
Assembling the box door with their own hands is presented in the video.
Then, drilling holes are made in the loop bar starting from the top hole, which should be located above the door hinges by 15 cm. Fix the correctly positioned door frame with screws. After the edges of the box are leveled, the door leaf is hung, followed by checking the operability of the door. The next stage will be the installation of foam between the installed door frame and the wall.
Inhibition of mounting foam should be carried out according to the recommendations of the material manufacturer. After the assembly foam has completely dried, pull out the spacers and wedges, and cut off the edge of the protruding foam.
How to install the collected box and door you kindly will prompt this video.
After installation of the door frame, additional elements and door casings are installed.
The additional elements for installation are pre-prepared in accordance with the size, considering the size of the groove for the installation.
Then the prepared additional element is firmly inserted into the groove of the box and is filled with mounting foam at the fastening points. The standard additional element from the manufacturer has a size of 190 mm. In the case where the width of the additional element does not allow to cover the width of the doorway, a connecting strip is used. The installation of additional elements is also simple, as is the installation of beautiful casings.
Installation of platbands
Any door, not equipped with beautiful casing in the tone of the door leaf, loses in a decorative design, and the appearance of the fasteners after installation is not encouraging. Therefore, the installation of door trims and the installation of doorways are the final stage of door installation.
Finishing the doorways with the platband will make it possible to hide the fastening elements of the door box installation. Installing the clypeus is a simple process if it is performed in accordance with the technological requirements for installation. Moreover, the building finishing material - the door casing is sold in ready for installation. To install the clypeus, you need to know its length.
Then the edges of the clypeus are sawed or cut at an angle of 45 degrees with the use of a chair or a sausage saw. The prepared clypeus is inserted into the groove of the door frame and fixed to the "liquid nails" at several points.
How to install the platbands with your own hands will help you with the video.
Door slopes with your own hands
After installing the doorframe and casing, the question arises as to improve the appearance of the doorway and hide the view from the view and the unevenness of the walls. Solve these tasks can and is necessary with the device of doorways. The ways of forming the doorways are as follows:
• by plastering
• the method of gluing the finishing material
• frame casing of the entire design of the slope with the use of finishing materials.
This separation of the slope device is due to the way in which they are formed. Ways to form slopes are sufficient, especially since for the slope device you can use:
• Drywall
• laminate
• panels
• MDF
• plastic.
and many other finishing materials.
Each finishing material can be safely called popular, because these materials allow us to put into practice a significant number of ready-made engineering solutions. In addition, the installation of slopes is the simplest work. The fact is that the question of fixing the elements of slopes is paramount and important. The most acceptable option for the formation of slopes with their own hands is the sealing of solutions and subsequent plastering. A slope of this type is obtained without internal voids, with a strong, non-bending surface, which increases the breaking resistance of the door structure.
The most common option is the formation of a skeleton of the frame type. In this case, the finishing material is installed and fastened to a frame made of metal profile or wooden bars. This variant of formation can be called "economy-variant". In addition, with the skeleton method, it is possible to achieve an equalization of the slope surface more quickly. The advantages of the frame method of forming a doorway include:
• ease of installation of electrical wiring and household electrical equipment
• Extended possibilities for finishing works
• relative cheapness of the slope device.
When forming a slope by a carcass method, it is recommended to fasten the elements using impact screws, as well as plastic dowels. To strengthen the construction between the bearing elements use jumpers. The upper corners between the sides of the opening and its upper part are to be reinforced.
How easy and affordable to form a doorway independently, without resorting to the services of masters, will prompt the video.
Loading ...